- #HOW TO REMOVE J CHANNEL FROM SLIDING GLASS DOOR INSTALL#
- #HOW TO REMOVE J CHANNEL FROM SLIDING GLASS DOOR PROFESSIONAL#
This allows a bank of doors to slide to any position during operation.Ī bolt which is designed to sit flush with the door when applied to the face or edge of the door. A fittings kit will contain all the hardware necessary to add an additional door to an existing system.Ī panel used in a sliding door system which is fixed and cannot be moved, allowing a sliding door to move in front or behind it.Ī folding door system where the doors are not hinged or pivoted to the opening frame. Our fire door hardware is positively appraised by Warrington Fire Research.Īdditional hardware to be used when more than one door is required for a sliding or folding system. Our fire door kit for sliding doors provides up to half an hour fire door assembly when purchased with a solid timber based fire door. This is only used in systems where there is a requirement for the hardware to be hidden.Ĭommonly used in pocket door systems, a finger pull is fitted to the thinnest side of a door to allow the sliding door to be easily pulled out when it is inside of the pocket.ĭoor hardware which helps prevent the spread of fire.
#HOW TO REMOVE J CHANNEL FROM SLIDING GLASS DOOR PROFESSIONAL#
An example of this would be a set of sliding doors which slide in front of an opening rather than within.Ī cover that is placed over the door hardware to give the system a more professional finish. When a track is installed on the front facing side of the opening. When the doors are folded open they are parked on one side of the side of the track. Used to describe a folding system whereby the door hardware is fitted to the end/corners of the doors. Also caps off the end of the track for aesthetic purposes. Used to stop a track from sliding out of its brackets, holding it securely in place. E ElbowsĪ section of Multidirectional track which changes the direction of the hanger. The measurement of the smallest side of a door. Its main function is to stop the door from travelling further than required and preventing damage via collision with the door and wall. D Door StopĪ fixed object which can be attached to the wall or floor. This is attached to a channel when set into concrete screed.Ī component used when fitting channel into a concrete screed to prevent removal when set. Hardware that is routed into the top of the door so it cannot be seen.Ī component used to join two channels together. When the doors are folded open they are parked equally either side of the track.Ī type of track stop which catches the door and holds it in place upon closure. Used to describe a folding system whereby the door hardware is fitted to the centre of the door. C CAD DrawingĪ 2D or 3D precision drawing which displays components and dimensions of a system. One side of the butt hinge is routed into the door and the other is attached to an adjacent door or frame. Sometimes known as a mortice hinge, a butt hinge is constructed of two matching metal panels connected by a pin and barrel system. Placed within the track, a brush strip prevents draft from passing through sliding door system. Brackets can accommodate multiple or single lines of track. Brackets can be soffit fixed to the underside of a lintel or ceiling, or they can be faced fixed to the side of a lintel or wall. A list of raw materials, components and parts which are used to manufacture an end product.Ĭomponents which are fastened to the building structure of the opening which supports the track. This system consists of two rollers located at the bottom of the door, allowing the door to run along the track below which carries the weight.īill of materials. orangeries, conservatories, out buildings and extensions. This type of system can be used in applications where top hung structural support is limited, e.g. Used in our Rustic 80 kit, this component is fitted between the door and the hanger to prevent the hanger from jumping off the track upon closure of the door. Side Plate - which saddles either side of the door (U shaped).Top Plate - which is fitted to the top of the door (flat).Angle Plate - which is fitted to the corner of a door (L shaped).
#HOW TO REMOVE J CHANNEL FROM SLIDING GLASS DOOR INSTALL#
P C Henderson aims to make it as easy as possible for customers to both specify and install our products, which is why we’ve developed our glossary of terms: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z A ApertureĪn opening whereby a sliding or folding system can be installed.Ī means of connection between a door and hanger. Sliding door hardware, particularly if you’re new to it, can often be quite a complex subject to understand.